MSFS 2020 airports mods

Seward Airport (icao: PAWD) is a small airport in Alaska, US serving Seward that is missing in MSFS basegame. I made the airport with satellite imagery, fixed terrain issues around it, and added details around the river next to the airport.

There are 2 runways, the primary runway 13/31 is 1295m long and the smaller runway 16/34 is 698m long.

GPS Coordinates: 60.130740, -149.418815

kui

Unzip the file into the Community folder

GPS Coordinates: 40.0725,116.5975

陈茂利

Unzip the file into the Community folder

GPS Coordinates: 29.719167,106.641667

陈茂利

LFFQ LA FERTE ALAIS Meeting de La Ferté Alais “Le temps des Hélices” Scenery made with the sdk of MSFS and and the magnificent models drawn from the internet with authorizations and licenses

Version 0.9
Improvement of models and buildings. Not mastering 3D software well it may take time for me. I need help.

Above all, a big thank you to Emmanuel BARANGER for his work and his kindness.In case of concern contact meIf you have the buildings and the hangar I’ll take them.

Please read the file :” important Read-me” in zip file Enjoy Christophe

Totof33120

Seitenstetten Airport (German: Flugplatz Seitenstetten, ICAO: LOLT) is a private use airport located 2 kilometres (1 mi) north-northeast of Seitenstetten, Lower Austria, Austria.

Latitude: 48° 3′ 0.40″
North Longitude: 14° 39′ 45.10″
East Elevation: 1053′ (321m) Max.
Runway Length: 2650′ (808m)
Runway info: Runway 10/28,
Surface: GRASS

Airport frequencies:
123.600 MHz private use

Photos for textures by Danny

Installation:
Copy folder “jb-lolt” from the ZIP file into the “Community” folder of your MSFS 2020 installation.

jb_AT

Fairmont Hot Springs is a very popular and busy resort airport located in BC’s southeastern portion of the province. It is a short VFR flight from Cranbrook and Calgary.

deltasim59er

The seaplane base is located on the territory of St Laurent de la Salanque, on the coast of the Salses pond. St Laurent is in the heart of the Salanque, along the road leading from the Perpignan-Nord motorway to Barcarès.

Brep

Disclaimer: I am totally aware, that I still have a lot to learn. My Blender skills are definitely not up to par with some of the guys on this site. This is especially true when it comes to texturework. For this reason, I have included a version of the airport that does not have custom buildings, just the autogen ones.

Update 1.0.1: Just a technical update, I have renamed the ‘modellib’ folder to not cause any issues.

Welcome To Mountain Air!

Mountain Air is a gated community in North Carolina. Homeowners and Members of Mountain Air Country Club can enjoy its many amenities all year round. Mountain Air is easily accessible with a car, however, it also has its own private airstrip. The airstrip is located atop a mountain, which makes landing a little bit more challenging than your usual rodeo. If it is your first time at Mountain Air, it is recommended to do a pass over the strip and get a feel for the surrounding area before attempting to land.
If in doubt, you can always check the Pilot’s Manual, published by non-other then the Mountain Air Pilot’s Association.
https://www.mapilots.org/wp-content/uploads/2018/10/Manual-Procedures-MAPA-1.5.pdf?x65557

Happy flying, happy golfing, and remember, always touch down before the 2000ft mark!

Features:
– Complete terraforming of the area. In the original version, 2NC0 is a flat airport atop the mountain. I made the required modifications to feel much closer to the real-life counterpart. Unfortunately, the SDK still has some limitations regarding terraforming, but I am pretty happy with the end result.
– 2 custom models for the main buildings. If you wish to use the airport without them please use the file from ‘NOCUSTOMBUILDINGS.ZIP’.
– VASI light added to the end of Runway 34. It has a 3.5 degree glideslope. Works the following way: Blinking white means above glideslope, steady white indicates glideslope, steady red indicates slightly under glideslope, blinking red indicates under glideslope.
– Many ‘default’ Asobo assets also added to the scene to give it more life
– 5 parking available, no FUEL.

Installion:
Normal version: Unzip the two files, and use ‘matemate-airport-2nc0-mountainair’ folder to copy into your community folder. You can discard the ‘NOCUSTOMBUILDINGS.ZIP’ if you want.
Autogen Buildings Version: Unzip the two files, then unzip ‘NOCUSTOMBUILDINGS.ZIP’, and use the folder inside to drop into your community folder. You can discard ‘matemate-airport-2nc0-mountainair’ folder if you want.

Future Plans:
This is release 1.0. For me this airport is a long term project. I continuously learn and improve on the way, in the long term, I would like to remake the two main buildings for higher quality, and add more local houses. For now, however, it’s quickfixes. Please if you find an issue or inaccuracy, let me know in the comments or direct message and I will try to fix it.

Hope you will all enjoy flying at Mountain Air!

This airport was created based on user request. I did quite grow to like it though, this is why I want to keep on developing it.

For updates on my current and upcoming projects, you can follow me on twitter: @matematemsfs

matemate